Ultra-low power consumption pinch valve
RV-001 series

Valve model No.	Wiring length	Connector of wiring
RV-001ZA	50 cm	Without connector
RV-001ZB	2 m	With connector
RV-001ZC	50 cm	With connector
Tubes are not included. Use tubes with the following dimensions as listed in the "Suitable Tubes" table below.   ◦TM-15 : ID 1.6 mm x OD 3.2 mm   ◦Others : ID 1/16 inch (1.59 mm) x       OD 1/8 inch (3.18 mm) When using the motor controller RE-V100, it is necessary to use the valve indicated "With connector".

Item	Specification
Rated voltage	DC 3V
Fluid pressure	0 to 150 kPa
Valve opening/closing time	0.3 sec or less
Pumping volume	5 µL or less
Tube durability	Over 150,000 cycles
Durability of the drive system	Over 500,000 cycles

Tube name	Manu- facturer	Remarks
Single-Use Silicone Tube Type V (High Durability Grade)	Shin-Etsu Polymer Co., Ltd.	Silicone rubber, USP Class VI
PharMed BPT	Saint- Gobain	Thermoplastic elastomer, USP Class VI
Versilon F-5500-A	Saint- Gobain	Fluoroelastomer
Transmaster TM-15	Mitsuboshi Co., Ltd.	Olefin-based
TYGON LMT-55	Saint- Gobain	Polyvinyl chloride resin, DEHP free
Use tubes with the following dimensions as listed in this table.   ◦TM-15 : ID 1.6 mm x OD 3.2 mm   ◦Others : ID 1/16 inch (1.59 mm) x       OD 1/8 inch (3.18 mm)

Tube name	Sterilization Method
	Auto- clave 121°C 25 min	EOG sterili- zation	Gamma ray sterili- zation 25 kGy or less
Single-Use Silicone Tube Type V (High Durability Grade)	Yes	Yes	Yes
PharMed BPT	Yes	Yes	Yes
Versilon F-5500-A	Uncon- firmed	Uncon- firmed	Uncon- firmed
Transmaster TM-15	No	Yes	Yes
TYGON LMT-55	No	Yes	Yes

Optional Tube model No.	Tubes used
AR-TBS1.6×3.2-K	Single-Use Silicone Tube Type V (High Durability Grade)
AR-TBF1.6×3.2-K	PharMed BPT
AR-TBR1.6×3.2-K	Versilon F-5500-A
AR-TBW1.6×3.2-K	Transmaster TM-15
AR-TBD1.6×3.2-K	TYGON LMT-55
The optional tube is a 24.5mm long suitable tube with special joints attached to both ends. And it can be easily attached to the valve. Optional tubes are sold in units of 10. The above model numbers are for a set of 10.

---

• There are five wires coming out of the valve, as shown in the photo to the left.
  There are two types of wire end process:
    ◦With connector
    ◦Only the insulation is stripped
          (Without connector)
• The length of the wiring is as shown in the "Standard model / Model No. & Specifications" table.
• The connector is for connecting to the motor controller RE-V100.
• The valve without connector can be operated by wiring as described below.

---

{ Wiring }

• Prepare a switch DPDT and a 3V DC power supply (DC power supply, dry cell, etc.).
• Connect the five wires coming out of the valve (red, orange, yellow, brown, and black) as shown in the diagram on the left.

{ Operation }

• When the switch is in the position shown in the diagram (red is positive, orange is negative), the valve opens.
• When the switch is in the opposite position to that shown in the diagram (yellow is positive, red is negative), the valve is closed.

---

---

For Ultra-low power consumption pinch valve RV-001 series,
Motor controller　RE-V100