Ring Pump RP-H series
| Download |
|---|
| Catalog (PDF) |
| Outline drawing (PDF) |
| 3D CAD data (STEP) |
| 2D CAD data (DXF) |
- Pump head replacement type capable of discharging up to 10mL/min.
- Pump head replacement is a one-touch method using strong magnets.
- The standard model is compatible with three types of motors: brushed DC motors, brushless DC motors, and stepper motors.
- The pump uses a brushless DC motor and a stepper motor achieved 5,000 hours∗1 of continuous operation by using needle roller bearings.
∗1: It is our experimental values using
water, and do not guarantee the
pump lifespan. - The pump head can be sterilized.
• Autoclave (25 minutes at 121℃) 10 times
is possible. However, pumps using
"Transmaster TM-15" tube can not be
autoclaved.
• Gamma ray sterilization (25kGy) is
possible.
| Type of drive motor | |||||
| Pump Model No. | |||||
|---|---|---|---|---|---|
| Volt- age (DC V) |
Dis- charge rate (mL/ min) |
Tube | Pump head model No. |
||
| ∗4 Material |
ID x OD (mm) |
||||
| Brushed DC motor | |||||
| RP-H02S-10Z-DC24V | |||||
| 24 | 3 - 10 | Silicone | 2.0 x 4.0 | RK- H02S |
|
| RP-H02F-10Z-DC24V | |||||
| 24 | 3 - 10 | PharMed BPT |
2.0 x 4.0 | RK- H02F |
|
| RP-H1.6S-7Z-DC24V | |||||
| 24 | 2 - 7 | Silicone | 1.6 x 3.2 | RK- H1.6S |
|
| RP-H1.6F-7Z-DC24V | |||||
| 24 | 2 - 7 | PharMed BPT |
1.6 x 3.2 | RK- H1.6F |
|
| RP-H1.6R-7Z-DC24V | |||||
| 24 | 2 - 7 | Versilon |
1.6 x 3.2 | RK- H1.6R |
|
| RP-H1.6W-7Z-DC24V | |||||
| 24 | 2 - 7 | Trans- master TM-15 |
1.6 x 3.2 | RK- H1.6W |
|
| Brushless DC motor∗2 | |||||
| RP-H02S-10Z-DC24VL | |||||
| 24 | 3 - 10 | Silicone | 2.0 x 4.0 | RK- H02S |
|
| RP-H02F-10Z-DC24VL | |||||
| 24 | 3 - 10 | PharMed BPT |
2.0 x 4.0 | RK- H02F |
|
| RP-H1.6S-7Z-DC24VL | |||||
| 24 | 2 - 7 | Silicone | 1.6 x 3.2 | RK- H1.6S |
|
| RP-H1.6F-7Z-DC24VL | |||||
| 24 | 2 - 7 | PharMed BPT |
1.6 x 3.2 | RK- H1.6F |
|
| RP-H1.6R-7Z-DC24VL | |||||
| 24 | 2 - 7 | Versilon |
1.6 x 3.2 | RK- H1.6R |
|
| RP-H1.6W-7Z-DC24VL | |||||
| 24 | 2 - 7 | Trans- master TM-15 |
1.6 x 3.2 | RK- H1.6W |
|
| Stepper motor∗3 | |||||
| RP-H02S-10Z-DC5VS | |||||
| 5 | 0.03 - 10 | Silicone | 2.0 x 4.0 | RK- H02S |
|
| RP-H02F-10Z-DC5VS | |||||
| 5 | 0.03 - 10 | PharMed BPT |
2.0 x 4.0 | RK- H02F |
|
| RP-H1.6S-7Z-DC5VS | |||||
| 5 | 0.02 - 7 | Silicone | 1.6 x 3.2 | RK- H1.6S |
|
| RP-H1.6F-7Z-DC5VS | |||||
| 5 | 0.02 - 7 | PharMed BPT |
1.6 x 3.2 | RK- H1.6F |
|
| RP-H1.6R-7Z-DC5VS | |||||
| 5 | 0.02 - 7 | Versilon |
1.6 x 3.2 | RK- H1.6R |
|
| RP-H1.6W-7Z-DC5VS | |||||
| 5 | 0.02 - 7 | Trans- master TM-15 |
1.6 x 3.2 | RK- H1.6W |
|
|
∗2. The brushless DC motor have a built-in driver board. The pump also comes with a 500mm long wire with a connector for connecting to the driver board. ∗3. A motor controller is necessary to drive the stepper motor. (A dedicated motor controller (RE-C700) sold separately is also available.) A 300mm long connection wire comes out from the stepper motor. The wiring does not have a connector for connecting RE-C700. The RE-C700 can be used with wiring without a connector, but we can also support wiring with a connector that makes it easy to connect to the RE-C700, so please contact us if you require it. ∗4. Some of Saint-Gobain's tube names are changed a few years ago. Versilon F-5500-A ↑ Fluran F-5500-A (Old name) |
|||||
Models using the DC brush motor
*Do not install the lead wire
in the downward direction.
- Discharge direction when the positive side of DC
power is connected to the terminal with the + mark
and the negative side is connected to the terminal
on the opposite side.
Models using the DC brushless motor
*Do not install the lead wire
in the downward direction.
- Discharge direction when
the rotation direction is
CW.
Models using the stepper motor
*Do not install the lead wire
in the downward direction.
- Discharge direction when
the rotation direction is
CW.
Driver board for brushless DC motor
The brushless DC motor used in the RP-H series has the built-in driver board.
The driver has the following functions: speed control, rotation direction switching, braking, and rotation signal output of 180 pulses per pump revolution.∗4
The pump is supplied with wiring with connectors for external connections.
The driver input/output details are as follows.
∗4 & 5 : Since the motor outputs 6 pulses per
revolution and the reduction gear ratio
is 1/30, the number of pulses per
revolution of the pump is 6 x 30 = 180.
